tc-cbq-details(8)
NAME
CBQ - Class Based Queueing
SYNOPSIS
tc qdisc ... dev dev ( parent classid | root) [ handle major: ] cbq avpkt bytes bandwidth rate [ cell bytes ] [ ewma log ] [ mpu bytes ] tc class ... dev dev parent major:[minor] [ classid major:minor ] cbq allot bytes [ bandwidth rate ] [ rate rate ] prio priority [ weight weight ] [ minburst packets ] [ maxburst packets ] [ ewma log ] [ cell bytes ] avpkt bytes [ mpu bytes ] [ bounded isolated ] [ split handle & defmap defmap ] [ estimator interval timeconstant ]
DESCRIPTION
Class Based Queueing is a classful qdisc that implements a rich linksharing hierarchy of classes. It contains shaping elements as well as prioritizing capabilities. Shaping is performed using link idle time calculations based on the timing of dequeue events and underlying link bandwidth.
SHAPING ALGORITHM
Shaping is done using link idle time calculations, and actions taken if these calculations deviate from set limits. When shaping a 10mbit/s connection to 1mbit/s, the link will be idle 90% of the time. If it isn't, it needs to be throttled so that it IS idle 90% of the time. From the kernel's perspective, this is hard to measure, so CBQ instead derives the idle time from the number of microseconds (in fact, jiffies) that elapse between requests from the device driver for more data. Combined with the knowledge of packet sizes, this is used to approximate how full or empty the link is. This is rather circumspect and doesn't always arrive at proper results. For example, what is the actual link speed of an interface that is not really able to transmit the full 100mbit/s of data, perhaps because of a badly implemented driver? A PCMCIA network card will also never achieve 100mbit/s because of the way the bus is designed - again, how do we calculate the idle time? The physical link bandwidth may be ill defined in case of not-quite- real network devices like PPP over Ethernet or PPTP over TCP/IP. The effective bandwidth in that case is probably determined by the efficiency of pipes to userspace - which not defined. During operations, the effective idletime is measured using an exponential weighted moving average (EWMA), which considers recent packets to be exponentially more important than past ones. The Unix loadaverage is calculated in the same way. The calculated idle time is subtracted from the EWMA measured one, the resulting number is called 'avgidle'. A perfectly loaded link has an avgidle of zero: packets arrive exactly at the calculated interval. An overloaded link has a negative avgidle and if it gets too negative, CBQ throttles and is then 'overlimit'. Conversely, an idle link might amass a huge avgidle, which would then allow infinite bandwidths after a few hours of silence. To prevent this, avgidle is capped at maxidle. If overlimit, in theory, the CBQ could throttle itself for exactly the amount of time that was calculated to pass between packets, and then pass one packet, and throttle again. Due to timer resolution constraints, this may not be feasible, see the minburst parameter below.
CLASSIFICATION
Within the one CBQ instance many classes may exist. Each of these classes contains another qdisc, by default tc-pfifo(8). When enqueueing a packet, CBQ starts at the root and uses various methods to determine which class should receive the data. If a verdict is reached, this process is repeated for the recipient class which might have further means of classifying traffic to its children, if any. CBQ has the following methods available to classify a packet to any child classes. (i) skb->priority class encoding. Can be set from userspace by an application with the SO_PRIORITY setsockopt. The skb->priority class encoding only applies if the skb->priority holds a major:minor handle of an existing class within this qdisc. (ii) tc filters attached to the class. (iii) The defmap of a class, as set with the split & defmap parameters. The defmap may contain instructions for each possible Linux packet priority. Each class also has a level. Leaf nodes, attached to the bottom of the class hierarchy, have a level of 0.
CLASSIFICATION ALGORITHM
Classification is a loop, which terminates when a leaf class is found.
At any point the loop may jump to the fallback algorithm.
The loop consists of the following steps:
(i) If the packet is generated locally and has a valid classid
encoded within its skb->priority, choose it and terminate.
(ii) Consult the tc filters, if any, attached to this child. If these
return a class which is not a leaf class, restart loop from the
class returned. If it is a leaf, choose it and terminate.
(iii) If the tc filters did not return a class, but did return a
classid, try to find a class with that id within this qdisc.
Check if the found class is of a lower level than the current
class. If so, and the returned class is not a leaf node, restart
the loop at the found class. If it is a leaf node, terminate.
If we found an upward reference to a higher level, enter the
fallback algorithm.
(iv) If the tc filters did not return a class, nor a valid reference
to one, consider the minor number of the reference to be the
priority. Retrieve a class from the defmap of this class for the
priority. If this did not contain a class, consult the defmap of
this class for the BEST_EFFORT class. If this is an upward
reference, or no BEST_EFFORT class was defined, enter the
fallback algorithm. If a valid class was found, and it is not a
leaf node, restart the loop at this class. If it is a leaf,
choose it and terminate. If neither the priority distilled from
the classid, nor the BEST_EFFORT priority yielded a class, enter
the fallback algorithm.
The fallback algorithm resides outside of the loop and is as follows.
(i) Consult the defmap of the class at which the jump to fallback
occured. If the defmap contains a class for the priority of the
class (which is related to the TOS field), choose this class and
terminate.
(ii) Consult the map for a class for the BEST_EFFORT priority. If
found, choose it, and terminate.
(iii) Choose the class at which break out to the fallback algorithm
occurred. Terminate.
The packet is enqueued to the class which was chosen when either
algorithm terminated. It is therefore possible for a packet to be
enqueued *not* at a leaf node, but in the middle of the hierarchy.
LINK SHARING ALGORITHM
When dequeuing for sending to the network device, CBQ decides which of its classes will be allowed to send. It does so with a Weighted Round Robin process in which each class with packets gets a chance to send in turn. The WRR process starts by asking the highest priority classes (lowest numerically - highest semantically) for packets, and will continue to do so until they have no more data to offer, in which case the process repeats for lower priorities. CERTAINTY ENDS HERE, ANK PLEASE HELP Each class is not allowed to send at length though - they can only dequeue a configurable amount of data during each round. If a class is about to go overlimit, and it is not bounded it will try to borrow avgidle from siblings that are not isolated. This process is repeated from the bottom upwards. If a class is unable to borrow enough avgidle to send a packet, it is throttled and not asked for a packet for enough time for the avgidle to increase above zero. I REALLY NEED HELP FIGURING THIS OUT. REST OF DOCUMENT IS PRETTY CERTAIN AGAIN.
QDISC
The root qdisc of a CBQ class tree has the following parameters:
parent major:minor | root
This mandatory parameter determines the place of the CBQ
instance, either at the root of an interface or within an
existing class.
handle major:
Like all other qdiscs, the CBQ can be assigned a handle. Should
consist only of a major number, followed by a colon. Optional.
avpkt bytes
For calculations, the average packet size must be known. It is
silently capped at a minimum of 2/3 of the interface MTU.
Mandatory.
bandwidth rate
To determine the idle time, CBQ must know the bandwidth of your
underlying physical interface, or parent qdisc. This is a vital
parameter, more about it later. Mandatory.
cell The cell size determines he granularity of packet transmission
time calculations. Has a sensible default.
mpu A zero sized packet may still take time to transmit. This value
is the lower cap for packet transmission time calculations -
packets smaller than this value are still deemed to have this
size. Defaults to zero.
ewma log
When CBQ needs to measure the average idle time, it does so
using an Exponentially Weighted Moving Average which smooths out
measurements into a moving average. The EWMA LOG determines how
much smoothing occurs. Defaults to 5. Lower values imply greater
sensitivity. Must be between 0 and 31.
A CBQ qdisc does not shape out of its own accord. It only needs to know
certain parameters about the underlying link. Actual shaping is done in
classes.
CLASSES
Classes have a host of parameters to configure their operation.
parent major:minor
Place of this class within the hierarchy. If attached directly
to a qdisc and not to another class, minor can be omitted.
Mandatory.
classid major:minor
Like qdiscs, classes can be named. The major number must be
equal to the major number of the qdisc to which it belongs.
Optional, but needed if this class is going to have children.
weight weight
When dequeuing to the interface, classes are tried for traffic
in a round-robin fashion. Classes with a higher configured qdisc
will generally have more traffic to offer during each round, so
it makes sense to allow it to dequeue more traffic. All weights
under a class are normalized, so only the ratios matter.
Defaults to the configured rate, unless the priority of this
class is maximal, in which case it is set to 1.
allot bytes
Allot specifies how many bytes a qdisc can dequeue during each
round of the process. This parameter is weighted using the
renormalized class weight described above.
priority priority
In the round-robin process, classes with the lowest priority
field are tried for packets first. Mandatory.
rate rate
Maximum rate this class and all its children combined can send
at. Mandatory.
bandwidth rate
This is different from the bandwidth specified when creating a
CBQ disc. Only used to determine maxidle and offtime, which are
only calculated when specifying maxburst or minburst. Mandatory
if specifying maxburst or minburst.
maxburst
This number of packets is used to calculate maxidle so that when
avgidle is at maxidle, this number of average packets can be
burst before avgidle drops to 0. Set it higher to be more
tolerant of bursts. You can't set maxidle directly, only via
this parameter.
minburst
As mentioned before, CBQ needs to throttle in case of overlimit.
The ideal solution is to do so for exactly the calculated idle
time, and pass 1 packet. However, Unix kernels generally have a
hard time scheduling events shorter than 10ms, so it is better
to throttle for a longer period, and then pass minburst packets
in one go, and then sleep minburst times longer.
The time to wait is called the offtime. Higher values of
minburst lead to more accurate shaping in the long term, but to
bigger bursts at millisecond timescales.
minidle
If avgidle is below 0, we are overlimits and need to wait until
avgidle will be big enough to send one packet. To prevent a
sudden burst from shutting down the link for a prolonged period
of time, avgidle is reset to minidle if it gets too low.
Minidle is specified in negative microseconds, so 10 means that
avgidle is capped at -10us.
bounded
Signifies that this class will not borrow bandwidth from its
siblings.
isolated
Means that this class will not borrow bandwidth to its siblings
split major:minor & defmap bitmap[/bitmap]
If consulting filters attached to a class did not give a
verdict, CBQ can also classify based on the packet's priority.
There are 16 priorities available, numbered from 0 to 15.
The defmap specifies which priorities this class wants to
receive, specified as a bitmap. The Least Significant Bit
corresponds to priority zero. The split parameter tells CBQ at
which class the decision must be made, which should be a
(grand)parent of the class you are adding.
As an example, 'tc class add ... classid 10:1 cbq .. split 10:0
defmap c0' configures class 10:0 to send packets with priorities
6 and 7 to 10:1.
The complimentary configuration would then be: 'tc class add ...
classid 10:2 cbq ... split 10:0 defmap 3f' Which would send all
packets 0, 1, 2, 3, 4 and 5 to 10:1.
estimator interval timeconstant
CBQ can measure how much bandwidth each class is using, which tc
filters can use to classify packets with. In order to determine
the bandwidth it uses a very simple estimator that measures once
every interval microseconds how much traffic has passed. This
again is a EWMA, for which the time constant can be specified,
also in microseconds. The time constant corresponds to the
sluggishness of the measurement or, conversely, to the
sensitivity of the average to short bursts. Higher values mean
less sensitivity.
SOURCES
o Sally Floyd and Van Jacobson, "Link-sharing and Resource
Management Models for Packet Networks", IEEE/ACM Transactions on
Networking, Vol.3, No.4, 1995
o Sally Floyd, "Notes on CBQ and Guarantee Service", 1995
o Sally Floyd, "Notes on Class-Based Queueing: Setting
Parameters", 1996
o Sally Floyd and Michael Speer, "Experimental Results for Class-
Based Queueing", 1998, not published.
SEE ALSO
tc(8)
AUTHOR
Alexey N. Kuznetsov, <kuznet@ms2.inr.ac.ru>. This manpage maintained by bert hubert <ahu@ds9a.nl>
Opportunity
Personal Opportunity - Free software gives you access to billions of dollars of software at no cost. Use this software for your business, personal use or to develop a profitable skill. Access to source code provides access to a level of capabilities/information that companies protect though copyrights. Open source is a core component of the Internet and it is available to you. Leverage the billions of dollars in resources and capabilities to build a career, establish a business or change the world. The potential is endless for those who understand the opportunity.
Business Opportunity - Goldman Sachs, IBM and countless large corporations are leveraging open source to reduce costs, develop products and increase their bottom lines. Learn what these companies know about open source and how open source can give you the advantage.
Free Software
Free Software provides computer programs and capabilities at no cost but more importantly, it provides the freedom to run, edit, contribute to, and share the software. The importance of free software is a matter of access, not price. Software at no cost is a benefit but ownership rights to the software and source code is far more significant.
Free Office Software - The Libre Office suite provides top desktop productivity tools for free. This includes, a word processor, spreadsheet, presentation engine, drawing and flowcharting, database and math applications. Libre Office is available for Linux or Windows.
Free Books
The Free Books Library is a collection of thousands of the most popular public domain books in an online readable format. The collection includes great classical literature and more recent works where the U.S. copyright has expired. These books are yours to read and use without restrictions.
Source Code - Want to change a program or know how it works? Open Source provides the source code for its programs so that anyone can use, modify or learn how to write those programs themselves. Visit the GNU source code repositories to download the source.
Education
Study at Harvard, Stanford or MIT - Open edX provides free online courses from Harvard, MIT, Columbia, UC Berkeley and other top Universities. Hundreds of courses for almost all major subjects and course levels. Open edx also offers some paid courses and selected certifications.
Linux Manual Pages - A man or manual page is a form of software documentation found on Linux/Unix operating systems. Topics covered include computer programs (including library and system calls), formal standards and conventions, and even abstract concepts.
