isdnctrl(8)
NAME
isdnctrl - get/set ISDN device information
SYNOPSIS
isdnctrl action device ...
DESCRIPTION
isdnctrl is used to create and delete network interfaces for ISDN, set up the various parameters and phone numbers for dial in and dial out. It is also used to list the current parameters of an already configured network interface. isdnctrl is not needed for configuration of ISDN ttys! The use of isdnctrl is independent of the hardware driver.
OPTIONS
The following actions may be given to isdnctrl.
addif name
Adds a new ISDN interface name to the kernel. If name is
omitted, the kernel will use ethX, where X is an increasing
number starting from 0. This is probably not useful with ISDN so
using a name like isdn0 (for raw ip interfaces) or ippp0 (for
synchronous PPP interfaces) is always recommended.
delif name [force]
Removes the ISDN interface name from the kernel. If the optional
keyword force is appended, isdnctrl executes ifconfig name down
before removing it.
reset [force]
Removes all ISDN interfaces from the kernel if it is possible.
If the optional keyword force is appended, isdnctrl executes
ifconfig name down before removing an interface.
ifdefaults name
resets the interface name to some reasonable defaults.
dialmode name [off|manual|auto]
Sets the dial mode of the interface to one of:
off
no connection can be made; an existing connection is terminated
immediately. Incoming connections are also not possible.
manual
manual dialing / hangup; a connection will only be made after
isdnctrl dial name but the line will be disconnected after the
huptimeout value set if using kernel drivers updated since 1 Nov
1998; otherwise an explicit isdnctrl hangup name will be needed
to cause the connection to be dropped.
Incoming connections are possible; however, if this interface is
configured in callback in mode, the callback dial will not
happen (as this is actually an outgoing connection, not an
incoming one).
auto
autodial mode; an outgoing packet will trigger a dialout, and a
hangup will occur after the huptimeout value specified (see
below).
An interface in auto dial mode will call another system back (if
configured in callback in mode).
auto was the "old" behaviour (as it was before dialmode was
implemented).
If no argument is given, the current dialmode value is
displayed.
You can give all as the interface name; the command will then be
executed for all interfaces.
addphone name out num
Adds the phone number num to the list of outgoing numbers of the
ISDN interface name. Numbers in this list are used to dial the
remote station if the connection is down and packets are to be
sent via the interface (Dial on demand). More than one number
can be set by calling isdnctrl addphone repeatedly. If more than
one number is set, these will be tried one after another (the
last added number is tried first, etc.). When using a german
SPV-type connection, the number has to be prefixed by a capital
S.
addphone name in num
Adds the phone number num to the list of incoming numbers of the
ISDN interface name. Numbers in this list are used to verify
access permission of the remote station if an incoming call is
received. The verification can be disabled by setting the
interface into insecure mode using isdnctrl name secure off. If
the list is empty, incoming calls are disabled. More than one
number can be added by calling isdnctrl addphone repeatedly.
Also wildcards can be used (see below).
delphone name in|out num
Removes phone number num from the incoming or outgoing phone
list.
eaz name [num]
Set the EAZ (German 1TR6 protocol) or MSN (Euro-ISDN E-DSS1) for
ISDN interface name to num. For an EAZ this is only one digit,
while for an MSN num is the whole MSN (usually the local phone
number). If num is omitted, isdnctrl prints the current setting
for ISDN interface name.
huptimeout name [seconds]
Set the hangup timeout for ISDN interface name to seconds. If
there is inactivity (i.e. no traffic on the interface) for the
given time the driver automatically shuts down the connection.
If seconds is omitted isdnctrl prints the current setting for
interface name.
cbdelay name [seconds]
Set the callback delay for ISDN interface name to seconds. If
callback mode for this interface is in, dialing is delayed the
given time. If the callback mode is out, after dialing out and
waiting the given time, a hangup is issued to free the line for
the incoming callback from the remote machine. This hangup-
after-dial is disabled by setting cbdelay to 0. If seconds is
omitted isdnctrl prints the current setting for interface name.
dialmax name [num]
Set the number of dial attempts for ISDN interface name to num.
If dialing, each phone number is tried this many times before
giving up. If num is omitted isdnctrl prints the current
setting for interface name.
ihup name [on|off]
Turn on or off the hangup timeout for incoming calls on
interface name. If on or off is omitted the current setting is
printed.
chargehup name [on|off]
Turn on or off hangup before next charge info for interface
name. This can only be used if the ISDN provider transmits
charge info during and after the connection. If set to on, the
driver will close the connection just before the next charge
info will be received if the interface is inactive. If on or off
is omitted the current setting is printed.
chargeint name [seconds]
If seconds are given, the charge interval for the given
interface is set. This may be useful on ISDN lines with no
chargeinfo or no online chargeinfo. The connection will be
closed 2 seconds before the end of the next estimated charge
interval if huptimeout seconds of inactivity have been reached.
If ihup is on, incoming connections are closed by this mechanism
also. On lines with online charge info you also might ask by
chargeint name for the current charge interval as delivered from
the telecom on a given interface.
secure name [on|off]
Turns on or off the security feature for interface name. If set
to on, incoming calls will only be accepted if the calling
number can be found in the incoming access list. See description
of action addphone for information about how to add numbers to
this list. If on or off is omitted, the current setting is
printed.
callback name [mode]
Set callback mode for interface name to mode mode. If callback
mode is in, then after getting an incoming call, a callback is
triggered. If callback mode is out, then the local system does
the initial call and then waits for callback of the remote
machine. The option on is available only for compatibility with
older versions. Its meaning is the same like in. If callback
mode is off, calls are handled normally without special
processing.
cbhup name [on|off]
Turns on or off Hangup (Reject) for interface name before
starting callback. If cbhup is on, when receiving an incoming
call, the interface first rejects that call before the callback
sequence is started. If on or off is omitted, the current
setting is printed.
encap name [encapsulation]
Set the encapsulation mode for interface name. Possible
encapsulations are:
rawip
raw ip encapsulation (default)
ip
IP + typefield encapsulation
cisco-h
Special mode for communicating with a Cisco in HDLC-mode with
Cisco-keepalive switched off.
ethernet
ethernet over ISDN (MAC-header included)
syncppp
Synchronous PPP over ISDN
uihdlc
raw ip with additional ui-header
cisco-hk
Special mode for communicating with a Cisco in HDLC-mode with
Cisco-keepalive switched on.
x25iface
Provides an interface as required by the Linux X.25 PLP protocol
implementation (requires Linux 2.1.x or newer).
If encapsulation is omitted, the current setting is printed.
l2_prot name [protocol]
Set the layer-2 protocol for interface name. Possible values
for protocol are:
x75i, x75ui, x75bui and hdlc. If protocol is omitted the
current setting is printed.
l3_prot name [ protocol ]
Set the layer-3 protocol for interface name. At the moment only
trans is supported here. If protocol is omitted the current
setting is printed.
list name
List all parameters and the charge info for interface name. If
name is all, then all interfaces are listed.
status name
Show the connection status for interface name. The output can
be one of the following types:
ippp0 not connected
There is no connection
ippp0 connected to 0123456789
There is an outgoing connection to phone number 0123456789
ippp0 connected from 0123456789
There is an incoming connection from phone number 0123456789
If the interface is connected, the exit status of the command is true,
else it is false.
If name is all, then the connection status for all interfaces is shown.
The exit status is always true in this case.
If name is active, then only those interfaces that are currently
connected are shown. The exit status is always true in this case.
verbose num
Set verbosity level to num.
hangup name
The connection of interface name is closed immediately.
bind name driverId,channel [exclusive]
Binds an interface name to a physical channel. The driverId
identifies a specific S0-Port. The channels of a port start
counting with zero. If exclusive is given, other interfaces
cannot use that channel anymore. Otherwise, the channel may be
used by other interfaces.
unbind name
Unbinds a the previously bound interface name.
pppbind name [num]
Binds the interface name to an ippp device /dev/ipppnum. This
works only for synchronous ppp. The value must be a number. If
num is omitted and name is called ipppX , then the interface is
bound to /dev/ipppX.
pppunbind name
Unbinds the previously bound interface name.
busreject driverId [on|off]
If switched on, instead of ignoring incoming calls not matching
any interface, isdn4linux responds with a REJECT to those calls.
If switched off, isdn4linux is passive, allowing other devices
connected to the same S0-bus to answer the call. You normally
should not enable this feature, if the ISDN adaptor is not the
only device connected to the S0-bus. Otherwise it could happen,
that isdn4linux rejects an incoming call which belongs to
another device on the bus.
addslave name slave
Adds a slave interface named slave to interface name for raw
channel-bundling. For bundling of more than two channels, any
number of slaves can be added to an interface by using this
command repeatedly. name must refer to an existing "master"
interface (not a slave). Slave interfaces are not visible to the
kernel, however all usual ISDN settings can be configured.
Because slave interfaces are not visible to the kernel, they are
configured "through" their "master", so it is important that
slave interfaces are added before the corresponding "master" is
started by ifconfig. If the "master" is already up, it has to
be shutdown with ifconfig down ... otherwise the addslave
command will be rejected.
sdelay name num
Set delay for slave-dialing. The master interface name has to
have a load of more than trigger cps for at least num seconds,
before its slave starts dialing.
Note that this only works for rawIP, not MPPP!
trigger name num
Set trigger level for slave-dialing. The master interface name
has to have a load of more than num cps for at least sdelay
seconds, before its slave starts dialing.
Note that this only works for rawIP, not MPPP!
addlink name
For MPPP, this adds a slave interface to the existing
connection, i.e. connect the extra channel now. It is like a
dial command for the extra channel.
This also means that addlink will only work if the master
interface name must already be connected! Also, the dialmode for
the slave interface must be auto.
removelink name
For MPPP, this removes a slave interface from the existing
connection, i.e. hangup the extra channel now.
dial name
Force dialing of interface name.
mapping driverId MSN0[,MSN1[,MSN2]] ... [,MSN9]
Installs a mapping-table for MSN<->EAZ-mapping. See README for
details.
WILDCARDS
When using isdnctrl addphone name in num to add phone numbers to the
incoming-call accept-list of an interface, wildcards similar to shell
wildcards can be used. The following wildcards are supported:
? one arbitrary digit
* zero or arbitrary number of digits
[list] one of the digits in list
[1-5] one digit in the range of (including) 1 and 5.
^ if this appears as the first character in a list, inverts the
list.
BUGS
This man page is not complete.
AUTHOR
Fritz Elfert <fritz@isdn4linux.de>
SEE ALSO
ttyI(4), isdnctrl(4), isdninfo(4), isdn_audio(4), isdn_cause(7).
Opportunity
Personal Opportunity - Free software gives you access to billions of dollars of software at no cost. Use this software for your business, personal use or to develop a profitable skill. Access to source code provides access to a level of capabilities/information that companies protect though copyrights. Open source is a core component of the Internet and it is available to you. Leverage the billions of dollars in resources and capabilities to build a career, establish a business or change the world. The potential is endless for those who understand the opportunity.
Business Opportunity - Goldman Sachs, IBM and countless large corporations are leveraging open source to reduce costs, develop products and increase their bottom lines. Learn what these companies know about open source and how open source can give you the advantage.
Free Software
Free Software provides computer programs and capabilities at no cost but more importantly, it provides the freedom to run, edit, contribute to, and share the software. The importance of free software is a matter of access, not price. Software at no cost is a benefit but ownership rights to the software and source code is far more significant.
Free Office Software - The Libre Office suite provides top desktop productivity tools for free. This includes, a word processor, spreadsheet, presentation engine, drawing and flowcharting, database and math applications. Libre Office is available for Linux or Windows.
Free Books
The Free Books Library is a collection of thousands of the most popular public domain books in an online readable format. The collection includes great classical literature and more recent works where the U.S. copyright has expired. These books are yours to read and use without restrictions.
Source Code - Want to change a program or know how it works? Open Source provides the source code for its programs so that anyone can use, modify or learn how to write those programs themselves. Visit the GNU source code repositories to download the source.
Education
Study at Harvard, Stanford or MIT - Open edX provides free online courses from Harvard, MIT, Columbia, UC Berkeley and other top Universities. Hundreds of courses for almost all major subjects and course levels. Open edx also offers some paid courses and selected certifications.
Linux Manual Pages - A man or manual page is a form of software documentation found on Linux/Unix operating systems. Topics covered include computer programs (including library and system calls), formal standards and conventions, and even abstract concepts.
