xsetwacom(1)
NAME
xsetwacom - commandline utility to query and modify wacom driver settings.
SYNOPSIS
xsetwacom [options] [command [arguments]]
DESCRIPTION
This program queries or changes properties on the devices loaded by the wacom driver. The modification of properties happens at runtime and is not persistent through X server restarts.
GENERAL OPTIONS
-d, --display display_name
Connect to the X server specified in display_name; see X(7).
-h, --help
Prints a short help.
-v, --verbose
Enable verbose output, useful for debugging.
-V, --version
Display version number and exit.
COMMANDS
Allowed commands are list, get, and set. The command may be specified
with or without one or two preceding dashes, i.e. --list is equivalent
to -list and list.
LIST COMMANDS
list devices
List known devices. Only input devices managed by the wacom
driver are listed.
list parameters
List known parameters. List all parameters suitable for the get
or the set command. Note that not all parameters are available
on all device types.
list modifiers
List the aliases for modifiers and other keys that can be used
when setting button action mappings.
GET COMMANDS
get device_name parameter
Get the current settings for the parameter on the given device.
Note that not all parameters are available on all device types.
The special parameter name "all" may be provided to display all
current settings on the device.
By default, options are printed on the commandline in the respective
format.
The output format may be altered with one of the following
options:
-s, --shell
Display the output in shell format, i.e. as shell commands to
xsetwacom to reproduce the same parameter.
-x, --xconf
Display the output in xorg.conf format, i.e. as option lines
that may be added to the InputDevice section in the xorg.conf.
SET COMMANDS
set device_name parameter [value]
Set the parameter value on the given device to the value
provided. Note that not all parameters are writable, some are
read-only and result in an error when trying to be modified.
PARAMETERS
Not all parameters are available on all tools. Use the get command
with the parameter or "all" parameter for specific input tool
applicable parameters and current settings.
Area x1 y1 x2 y2
Set the tablet input area in device coordinates in the form top
left x/y and bottom right x/y. Top left and bottom right are
defined in the device's native orientation, regardless of the
actual rotation currently applied. Input outside of these
coordinates will be clipped to the edges of the area defined.
Default: 0 0 x2 y2; with x2 and y2 tablet specific.
Button button-number [mapping]
Set a mapping for the specified button-number. Mappings take the
form of either a single numeric button or an 'action' to be
performed. If no mapping is provided, the default mapping is
restored.
Numeric button mappings indicate what X11 button number the
given button-number should correspond to. For example, a mapping
of "3" means a press of the given button-number will produce a
press of X11 button 3 (i.e. right click).
Action mappings allow button presses to perform many events.
They take the form of a string of keywords and arguments.
The "key" keyword is following by a list of key names. These can
optionally be preceded by "+" for press and "-" for release. If
+/- is not given, press-and-release is assumed, except for
modifier keys which are left pressed. Key names can be X11
KeySyms or some aliases such as 'shift' or 'f1' (the full list
can be seen with the list modifiers command).
For example, "key +a +shift b -shift -a" converts the button
into a series of keystrokes, in this example "press a, press
shift, press and release b, release shift, release a".
The "button" keyword is similar except that its arguments are
X11 button numbers.
The "modetoggle" keyword is also recognized; it takes no
arguments, and toggles the device mode between relative and
absolute pointer tracking.
The events in the action mapping are sent when the physical
button is pressed. If the action mapping leaves any buttons or
keys pressed (such as a modifier key), they will be released
when the physical button is released.
Multiple keywords may be present in one action if desired: for
example "key +ctrl button 5 key -ctrl". Each keyword takes all
arguments until the next keyword.
A maximum of 256 presses and/or releases can be specified in an
action mapping.
The driver can only simulate physical key events but not keysyms
and xsetwacom translates the mapping sequence into such events.
Thus, symbols on the same physical key will generate the same
event. For example, '1' and '!' are on the same key on a US
keyboard and thus have the same keycode). For access to keys on
a higher shift level, the sequence should be entered as it would
be typed on a physical keyboard. For example, a exclamation mark
is entered by the sequence of "key +shift 1 -shift".
BindToSerial [serial|0]
Bind the device to the tool with the specified serial number.
Once bound, the device will ignore events from other tools. A
serial of 0 means the device is unbound and will react to any
tool of the matching type. Default: 0
MapToOutput [output]
Map the tablet's input area to a given output (e.g. "VGA1").
Output names may either be the name of a head available through
the XRandR extension, or an X11 geometry string of the form
WIDTHxHEIGHT+X+Y. To switch to the next available output, the
"next" keyword is also supported. This will cycle between the
individual monitors connected to the system, and then the entire
desktop. The mapping may be reset to the entire desktop at any
time with the output name "desktop". Users of the NVIDIA binary
driver should use the output names "HEAD-0" and "HEAD-1" until
the driver supports XRandR 1.2 or later.
The output mapping configuration is a onetime setting and does
not track output reconfigurations; the command needs to be re-
run whenever the output configuration changes. When used with
tablet rotation, the tablet must be rotated before it is mapped
to the new screen. This parameter is write-only and cannot be
queried.
Mode Absolute|Relative
Set the device mode as either Relative or Absolute. Relative
means pointer tracking for the device will function like a
mouse, whereas Absolute means the pointer corresponds to the
device's actual position on the tablet or tablet PC screen.
Default: Absolute for stylus, eraser and tablet PC touch;
Relative for cursor and tablet touch.
PressureCurve x1 y1 x2 y2
A Bezier curve of third order, composed of two anchor points
(0,0 and 100,100) and two user modifiable control points that
define the curve's shape. Raise the curve (x1<y1 x2<y2) to
"soften" the feel and lower the curve (x1>y1 x2>y2) for a
"firmer" feel. Sigmoid shaped curves are permitted (x1>y1 x2<y2
or x1<y1 x2>y2). Default: 0 0 100 100, a linear curve; range
of 0 to 100 for all four values.
RawSample level
Set the sample window size (a sliding average sampling window)
for incoming input tool raw data points. Default: 4, range of
1 to 20.
Rotate none|half|cw|ccw
Set the tablet to the given rotation:
none: the tablet is not rotated and uses its natural rotation
half: the tablet is rotated by 180 degrees (upside-down)
cw: the tablet is rotated 90 degrees clockwise
ccw: the tablet is rotated 90 degrees counter-clockwise
Rotation is a tablet-wide option: rotation of one tool affects
all other tools associated with the same tablet. When the tablet
is physically rotated, rotate any tool to the corresponding
orientation. Default: none
Suppress level
Set the delta (difference) cutoff level for further processing
of incoming input tool coordinate values. For example a X or Y
coordinate event will be sent only if the change between the
current X or Y coordinate and the previous one is greater than
the Suppress value. The same applies to pressure level (Z
coordinate) and Tilt rotation values. With a current absolute
wheel (AbsWheel) or Tilt value the delta between it and the
previous value must be equal to or greater than the Suppress
value in order to be sent on. Suppress is a tablet wide
parameter. A specified delta level for one input tool is
applied to all input tool coordinates. To disable suppression
use a level of 0. Default: 2, range of 0 to 100.
TabletDebugLevel level
Set the debug level for this tablet to the given level. This
only affects code paths that are shared between several tools on
the same physical tablet. A higher level means more fine-grained
debug messages, a level of 0 turns debugging off for this tool.
Requires the driver to be built with debugging enabled. See also
ToolDebugLevel. Default: 0, range of 0 to 12.
TabletPCButton on|off
If on, the stylus must be in contact with the screen for a
stylus side button to work. If off, stylus buttons will work
once the stylus is in proximity of the tablet (regardless of
whether it is touching the screen). Default: on for Tablet
PCs; off for all other models.
ToolSerialPrevious
Get the serial number of the tool that was last in proximity
last. This serial number is updated whenever the tool goes out
of proximity. If the current tool went out of proximity once,
this serial number is the one of the current tool. This is a
read-only parameter.
Touch on|off
If on, touch events are reported to userland, i.e., system
cursor moves when user touches the tablet. If off, touch events
are ignored. Default: on for devices that support touch; off for
all other models.
HWTouchSwitchState on|off
If on, it means touch switch is turned off. That is, touch
events are reported to userland. If off, touch switch is turned
on, i.e., touch events are ignored. This is a read-only
parameter. Initial touch switch state is retrieved from the
kernel when X driver starts.
CursorProximity distance
sets the max distance from tablet to stop reporting movement for
cursor in relative mode. Default for Intuos series is 10, for
Graphire series (including Volitos) is 42. Only available for
the cursor/puck device.
Threshold level
Set the minimum pressure necessary to generate a Button event
for the stylus tip, eraser, or touch. The pressure levels of
all tablets are normalized to 2048 levels irregardless of the
actual hardware supported levels. This parameter is independent
of the PressureCurve parameter. Default: 27, range of 0 to
2047.
ToolDebugLevel level
Set the debug level for this tool to the given level. This only
affects code paths that are specific to a given tool. A higher
level means more fine-grained debug messages, a level of 0 turns
debugging off for this tool. Requires the driver to be built
with debugging enabled. See also TabletDebugLevel. Default: 0,
range of 0 to 12.
PressureRecalibration on|off
If the initial pressure of a device is != 0 the driver
recalibrates the pressure range. This is to account for worn out
devices. The downside is that when the user hits the tablet
very hard the initial pressure reading may be unequal to zero
even for a perfectly good pen. If the consecutive pressure
readings are not higher than the initial pressure by a threshold
no button event will be generated. This option allows to
disable the recalibration. Default: on
AUTHORS
Peter Hutterer <peter.hutterer@redhat.com>
SEE ALSO
Xorg(1), wacom(4), xorg.conf(5), X(7) More information is available at http://linuxwacom.sourceforge.net
Opportunity
Personal Opportunity - Free software gives you access to billions of dollars of software at no cost. Use this software for your business, personal use or to develop a profitable skill. Access to source code provides access to a level of capabilities/information that companies protect though copyrights. Open source is a core component of the Internet and it is available to you. Leverage the billions of dollars in resources and capabilities to build a career, establish a business or change the world. The potential is endless for those who understand the opportunity.
Business Opportunity - Goldman Sachs, IBM and countless large corporations are leveraging open source to reduce costs, develop products and increase their bottom lines. Learn what these companies know about open source and how open source can give you the advantage.
Free Software
Free Software provides computer programs and capabilities at no cost but more importantly, it provides the freedom to run, edit, contribute to, and share the software. The importance of free software is a matter of access, not price. Software at no cost is a benefit but ownership rights to the software and source code is far more significant.
Free Office Software - The Libre Office suite provides top desktop productivity tools for free. This includes, a word processor, spreadsheet, presentation engine, drawing and flowcharting, database and math applications. Libre Office is available for Linux or Windows.
Free Books
The Free Books Library is a collection of thousands of the most popular public domain books in an online readable format. The collection includes great classical literature and more recent works where the U.S. copyright has expired. These books are yours to read and use without restrictions.
Source Code - Want to change a program or know how it works? Open Source provides the source code for its programs so that anyone can use, modify or learn how to write those programs themselves. Visit the GNU source code repositories to download the source.
Education
Study at Harvard, Stanford or MIT - Open edX provides free online courses from Harvard, MIT, Columbia, UC Berkeley and other top Universities. Hundreds of courses for almost all major subjects and course levels. Open edx also offers some paid courses and selected certifications.
Linux Manual Pages - A man or manual page is a form of software documentation found on Linux/Unix operating systems. Topics covered include computer programs (including library and system calls), formal standards and conventions, and even abstract concepts.
