shorewall6-providers(5)
NAME
providers - Shorewall6 Providers file
SYNOPSIS
/etc/shorewall6/providers
DESCRIPTION
This file is used to define additional routing tables. You will want to
define an additional table if:
* You have connections to more than one ISP or multiple connections
to the same ISP
* You run Squid as a transparent proxy on a host other than the
firewall.
* You have other requirements for policy routing.
Each entry in the file defines a single routing table.
If you wish to omit a column entry but want to include an entry in the
next column, use "-" for the omitted entry.
The columns in the file are as follows.
NAME - name
The provider name. Must be a valid shell variable name. The names
'local', 'main', 'default' and 'unspec' are reserved and may not be
used as provider names.
NUMBER - number
The provider number -- a number between 1 and 15. Each provider
must be assigned a unique value.
MARK (Optional) - value
A FWMARK value used in your shorewall6-mangle[1](5) file to direct
packets to this provider.
If HIGH_ROUTE_MARKS=Yes in shorewall6.conf[2](5), then the value
must be a multiple of 256 between 256 and 65280 or their
hexadecimal equivalents (0x0100 and 0xff00 with the low-order byte
of the value being zero). Otherwise, the value must be between 1
and 255. Each provider must be assigned a unique mark value. This
column may be omitted if you don't use packet marking to direct
connections to a particular provider.
DUPLICATE - routing-table-name
The name of an existing table to duplicate to create this routing
table. May be main or the name of a previously listed provider. You
may select only certain entries from the table to copy by using the
COPY column below.
INTERFACE - interface
The name of the network interface to the provider. Must be listed
in shorewall6-interfaces[3](5).
GATEWAY - {-|address|detect|none}
The IP address of the provider's gateway router.
You can enter detect here and Shorewall6 will attempt to detect the
gateway automatically.
Beginning with Shorewall 5.0.6, you may also enter none. This
causes creation of a routing table with no default route in it.
For PPP devices, you may omit this column.
OPTIONS (Optional) - [-|option[,option]...]
A comma-separated list selected from the following. The order of
the options is not significant but the list may contain no embedded
white-space.
autosrc
Added in Shorewall 4.5.17. Causes a host route to the
provider's gateway router to be added to the provider's routing
table. This is the default behavior unless overridden by a
following noautosrc option.
balance[=weight]
Added in Shorewall 4.4.25. The providers that have balance
specified will get outbound traffic load-balanced among them.
By default, all interfaces with balance specified will have the
same weight (1). Beginning with Shorewall 5.0.13, you can
change the weight of an interface by specifying balance=weight
where weight is the weight of the route out of this interface.
Prior to Shorewall 5.0.13, only one provider can specify this
option.
fallback[=weight]
Added in Shorewall 4.4.25. Indicates that a default route
through the provider should be added to the default routing
table (table 253). If a weight is given, a balanced route is
added with the weight of this provider equal to the specified
weight. If the option is given without a weight, an separate
default route is added through the provider's gateway; the
route has a metric equal to the provider's NUMBER. Prior to
Shorewall 5.0.13, at most one provider can specify this option
and a weight may not be given.
track
If specified, inbound connections on this interface are to be
tracked so that responses may be routed back out this same
interface.
You want to specify track if internet hosts will be connecting
to local servers through this provider.
Beginning with Shorewall 4.4.3, track defaults to the setting
of the TRACK_PROVIDERS option in shorewall6.conf[4] (5). If you
set TRACK_PROVIDERS=Yes and want to override that setting for
an individual provider, then specify notrack (see below).
loose
Shorewall6 normally adds a routing rule for each IP address on
an interface which forces traffic whose source is that IP
address to be sent using the routing table for that interface.
Setting loose prevents creation of such rules on this
interface.
load=probability
Added in Shorewall 4.6.0. This option provides an alternative
method of load balancing based on probabilities. Providers to
be balanced are given a probability (a number 0 > n >= 1) with
up to 8 digits to the right of the decimal point. Beginning
with Shorewall 4.6.10, a warning is issued if the sum of the
probabilities is not 1.00000000.
noautosrc
Added in Shorewall 4.5.17. Prevents the addition of a host
route to the provider's gateway router from being added to the
provider's routing table. This option must be used with caution
as it can cause start and restart failures.
notrack
Added in Shorewall 4.4.3. When specified, turns off track.
optional (deprecated for use with providers that do not share an
interface)
If the interface named in the INTERFACE column is not up and
configured with an IPv4 address then ignore this provider. If
not specified, the value of the optional option for the
INTERFACE in shorewall6-interfaces(5)[3] is assumed. Use of
that option is preferred to this one, unless an address is
provider in the INTERFACE column.
primary
Added in Shorewall 4.6.6, primary is a synonym for balance (see
above) and is preferred when the remaining providers specify
fallback or tproxy.
src=source-address
Specifies the source address to use when routing to this
provider and none is known (the local client has bound to the 0
address). May not be specified when an address is given in the
INTERFACE column. If this option is not used, Shorewall6
substitutes the primary IP address on the interface named in
the INTERFACE column.
mtu=number
Specifies the MTU when forwarding through this provider. If not
given, the MTU of the interface named in the INTERFACE column
is assumed.
tproxy
Added in Shorewall 4.5.4. Used for supporting the TPROXY action
in shorewall-tcrules(5). See
http://www.shorewall.net/Shorewall_Squid_Usage.html[5]. When
specified, the MARK, DUPLICATE and GATEWAY columns should be
empty, INTERFACE should be set to 'lo' and tproxy should be the
only OPTION. Only one tproxy provider is allowed.
hostroute
Added in Shorewall 4.5.21. This is the default behavior that
results in a host route to the defined GATEWAY being inserted
into the main routing table and into the provider's routing
table. hostroute is required for older distributions but
nohostroute (below) is appropriate for recent distributions.
hostroute may interfere with Zebra's ability to add routes on
some distributions such as Debian 7.
nohostroute
Added in Shorewall 4.5.21. nohostroute inhibits addition of a
host route to the defined GATEWAY being inserted into the main
routing table and into the provider's routing table.
nohostroute is not appropriate for older distributions but is
appropriate for recent distributions. nohostroute allows
Zebra's to correctly add routes on some distributions such as
Debian 7.
persistent
Added in Shorewall 5.0.2 and alters the behavior of the disable
command:
* The provider's routing table still contains the apprioriate
default route.
* Unless the noautosrc option is specified, routing rules are
generated to route traffic from the interfaces address(es)
out of the provider's routing table.
* Persistent routing rules in shorewall6-rtrules(5)[6] are
present.
Note
The generated script will attempt to reenable a disabled
persistent provider during execution of the start, restart
and reload commands. When persistent is not specified, only
the enable and reenable commands can reenable the provider.
COPY - [{none|interface[,interface]...}]
A comma-separated list of other interfaces on your firewall.
Wildcards specified using an asterisk ("*") are permitted (e.g.,
tun* ). Usually used only when DUPLICATE is main. Only copy routes
through INTERFACE and through interfaces listed here. If you only
wish to copy routes through INTERFACE, enter none in this column.
Beginning with Shorewall 4.5.17, blackhole, unreachable and
prohibit routes are no longer copied by default but may be copied
by including blackhole,unreachable and prohibit respectively in the
COPY list.
EXAMPLES
Example 1:
You run squid in your DMZ on IP address 2002:ce7c:92b4:1::2. Your
DMZ interface is eth2
#NAME NUMBER MARK DUPLICATE INTERFACE GATEWAY OPTIONS
Squid 1 1 - eth2 2002:ce7c:92b4:1::2 -
Example 2:
eth0 connects to ISP 1. The ISP's gateway router has IP address
2001:ce7c:92b4:1::2.
eth1 connects to ISP 2. The ISP's gateway router has IP address
2001:d64c:83c9:12::8b.
eth2 connects to a local network.
#NAME NUMBER MARK DUPLICATE INTERFACE GATEWAY OPTIONS COPY
ISP1 1 1 main eth0 2001:ce7c:92b4:1::2 track eth2
ISP2 2 2 main eth1 2001:d64c:83c9:12::8b track eth2
FILES
/etc/shorewall6/providers
SEE ALSO
http://www.shorewall.net/MultiISP.html[7] http://www.shorewall.net/configuration_file_basics.htm#Pairs[8] shorewall6(8), shorewall6-accounting(5), shorewall6-actions(5), shorewall6-blacklist(5), shorewall6-hosts(5), shorewall6-interfaces(5), shorewall6-maclist(5), shorewall6-netmap(5),shorewall6-params(5), shorewall6-policy(5), shorewall6-rtrules(5), shorewall6-routestopped(5), shorewall6-rules(5), shorewall6.conf(5), shorewall6-secmarks(5), shorewall6-tcclasses(5), shorewall6-tcdevices(5), shorewall6-mangle(5), shorewall6-tos(5), shorewall6-tunnels(5), shorewall6-zones(5)
NOTES
1. shorewall6-mangle
http://www.shorewall.net/manpages6/shorewall6-mangle.html
2. shorewall6.conf
http://www.shorewall.net/manpages6/shorewall6.conf.html
3. shorewall6-interfaces
http://www.shorewall.net/manpages6/shorewall6-interfaces.html
4. shorewall6.conf
http://www.shorewall.net/manpages6/shorwewall6.conf.html
5. http://www.shorewall.net/Shorewall_Squid_Usage.html
http://www.shorewall.net/Shorewall_Squid_Usage.html
6. shorewall6-rtrules(5)
http://www.shorewall.netshorewall-rtrules.html
7. http://www.shorewall.net/MultiISP.html
http://www.shorewall.net/MultiISP.html
8. http://www.shorewall.net/configuration_file_basics.htm#Pairs
http://www.shorewall.net/configuration_file_basics.htm#Pairs
Opportunity
Personal Opportunity - Free software gives you access to billions of dollars of software at no cost. Use this software for your business, personal use or to develop a profitable skill. Access to source code provides access to a level of capabilities/information that companies protect though copyrights. Open source is a core component of the Internet and it is available to you. Leverage the billions of dollars in resources and capabilities to build a career, establish a business or change the world. The potential is endless for those who understand the opportunity.
Business Opportunity - Goldman Sachs, IBM and countless large corporations are leveraging open source to reduce costs, develop products and increase their bottom lines. Learn what these companies know about open source and how open source can give you the advantage.
Free Software
Free Software provides computer programs and capabilities at no cost but more importantly, it provides the freedom to run, edit, contribute to, and share the software. The importance of free software is a matter of access, not price. Software at no cost is a benefit but ownership rights to the software and source code is far more significant.
Free Office Software - The Libre Office suite provides top desktop productivity tools for free. This includes, a word processor, spreadsheet, presentation engine, drawing and flowcharting, database and math applications. Libre Office is available for Linux or Windows.
Free Books
The Free Books Library is a collection of thousands of the most popular public domain books in an online readable format. The collection includes great classical literature and more recent works where the U.S. copyright has expired. These books are yours to read and use without restrictions.
Source Code - Want to change a program or know how it works? Open Source provides the source code for its programs so that anyone can use, modify or learn how to write those programs themselves. Visit the GNU source code repositories to download the source.
Education
Study at Harvard, Stanford or MIT - Open edX provides free online courses from Harvard, MIT, Columbia, UC Berkeley and other top Universities. Hundreds of courses for almost all major subjects and course levels. Open edx also offers some paid courses and selected certifications.
Linux Manual Pages - A man or manual page is a form of software documentation found on Linux/Unix operating systems. Topics covered include computer programs (including library and system calls), formal standards and conventions, and even abstract concepts.
