mouse - serial mouse interface
Serial mice are connected to a serial RS232/V24 dialout line, see ttyS(4) for a description.
Introduction
The pinout of the usual 9 pin plug as used for serial mice is:
pin name used for
2 RX Data
3 TX -12 V, Imax = 10 mA
4 DTR +12 V, Imax = 10 mA
7 RTS +12 V, Imax = 10 mA
5 GND Ground
This is the specification, in fact 9 V suffices with most mice.
The mouse driver can recognize a mouse by dropping RTS to low and
raising it again. About 14 ms later the mouse will send 0x4D ('M') on
the data line. After a further 63 ms, a Microsoft-compatible 3-button
mouse will send 0x33 ('3').
The relative mouse movement is sent as dx (positive means right) and dy
(positive means down). Various mice can operate at different speeds.
To select speeds, cycle through the speeds 9600, 4800, 2400, and 1200
bit/s, each time writing the two characters from the table below and
waiting 0.1 seconds. The following table shows available speeds and
the strings that select them:
bit/s string
9600 *q
4800 *p
2400 *o
1200 *n
The first byte of a data packet can be used for synchronization
purposes.
Microsoft protocol
The Microsoft protocol uses 1 start bit, 7 data bits, no parity and one
stop bit at the speed of 1200 bits/sec. Data is sent to RxD in 3-byte
packets. The dx and dy movements are sent as two's-complement, lb (rb)
are set when the left (right) button is pressed:
byte d6 d5 d4 d3 d2 d1 d0
1 1 lb rb dy7 dy6 dx7 dx6
2 0 dx5 dx4 dx3 dx2 dx1 dx0
3 0 dy5 dy4 dy3 dy2 dy1 dy0
3-button Microsoft protocol
Original Microsoft mice only have two buttons. However, there are some
three button mice which also use the Microsoft protocol. Pressing or
releasing the middle button is reported by sending a packet with zero
movement and no buttons pressed. (Thus, unlike for the other two
buttons, the status of the middle button is not reported in each
packet.)
Logitech protocol
Logitech serial 3-button mice use a different extension of the
Microsoft protocol: when the middle button is up, the above 3-byte
packet is sent. When the middle button is down a 4-byte packet is
sent, where the 4th byte has value 0x20 (or at least has the 0x20 bit
set). In particular, a press of the middle button is reported as
0,0,0,0x20 when no other buttons are down.
Mousesystems protocol
The Mousesystems protocol uses 1 start bit, 8 data bits, no parity and
two stop bits at the speed of 1200 bits/sec. Data is sent to RxD in
5-byte packets. dx is sent as the sum of the two two's-complement
values, dy is send as negated sum of the two two's-complement values.
lb (mb, rb) are cleared when the left (middle, right) button is
pressed:
byte d7 d6 d5 d4 d3 d2 d1 d0
1 1 0 0 0 0 lb mb rb
2 0 dxa6 dxa5 dxa4 dxa3 dxa2 dxa1 dxa0
3 0 dya6 dya5 dya4 dya3 dya2 dya1 dya0
4 0 dxb6 dxb5 dxb4 dxb3 dxb2 dxb1 dxb0
5 0 dyb6 dyb5 dyb4 dyb3 dyb2 dyb1 dyb0
Bytes 4 and 5 describe the change that occurred since bytes 2 and 3
were transmitted.
Sun protocol
The Sun protocol is the 3-byte version of the above 5-byte Mousesystems
protocol: the last two bytes are not sent.
MM protocol
The MM protocol uses 1 start bit, 8 data bits, odd parity and one stop
bit at the speed of 1200 bits/sec. Data is sent to RxD in 3-byte
packets. dx and dy are sent as single signed values, the sign bit
indicating a negative value. lb (mb, rb) are set when the left
(middle, right) button is pressed:
byte d7 d6 d5 d4 d3 d2 d1 d0
1 1 0 0 dxs dys lb mb rb
2 0 dx6 dx5 dx4 dx3 dx2 dx1 dx0
3 0 dy6 dy5 dy4 dy3 dy2 dy1 dy0
/dev/mouse
A commonly used symbolic link pointing to a mouse device.
ttyS(4), gpm(8)
This page is part of release 4.09 of the Linux man-pages project. A description of the project, information about reporting bugs, and the latest version of this page, can be found at https://www.kernel.org/doc/man-pages/.
Personal Opportunity - Free software gives you access to billions of dollars of software at no cost. Use this software for your business, personal use or to develop a profitable skill. Access to source code provides access to a level of capabilities/information that companies protect though copyrights. Open source is a core component of the Internet and it is available to you. Leverage the billions of dollars in resources and capabilities to build a career, establish a business or change the world. The potential is endless for those who understand the opportunity.
Business Opportunity - Goldman Sachs, IBM and countless large corporations are leveraging open source to reduce costs, develop products and increase their bottom lines. Learn what these companies know about open source and how open source can give you the advantage.
Free Software provides computer programs and capabilities at no cost but more importantly, it provides the freedom to run, edit, contribute to, and share the software. The importance of free software is a matter of access, not price. Software at no cost is a benefit but ownership rights to the software and source code is far more significant.
Free Office Software - The Libre Office suite provides top desktop productivity tools for free. This includes, a word processor, spreadsheet, presentation engine, drawing and flowcharting, database and math applications. Libre Office is available for Linux or Windows.
The Free Books Library is a collection of thousands of the most popular public domain books in an online readable format. The collection includes great classical literature and more recent works where the U.S. copyright has expired. These books are yours to read and use without restrictions.
Source Code - Want to change a program or know how it works? Open Source provides the source code for its programs so that anyone can use, modify or learn how to write those programs themselves. Visit the GNU source code repositories to download the source.
Study at Harvard, Stanford or MIT - Open edX provides free online courses from Harvard, MIT, Columbia, UC Berkeley and other top Universities. Hundreds of courses for almost all major subjects and course levels. Open edx also offers some paid courses and selected certifications.
Linux Manual Pages - A man or manual page is a form of software documentation found on Linux/Unix operating systems. Topics covered include computer programs (including library and system calls), formal standards and conventions, and even abstract concepts.